|
Welcome to the Piano World Piano Forums Over 3 million posts about pianos, digital pianos, and all types of keyboard instruments. Over 100,000 members from around the world.
Join the World's Largest Community of Piano Lovers
(it's free)
It's Fun to Play the Piano ... Please Pass It On!
|
|
69 members (Abdulrohmanoman, Charles Cohen, accordeur, BWV846, Animisha, benkeys, Anglagard44, 12 invisible),
2,309
guests, and
436
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
Joined: Oct 2008
Posts: 156
Full Member
|
OP
Full Member
Joined: Oct 2008
Posts: 156 |
I have been asked to tune a player piano next week.I have never serviced one.What are some general procedures to removing the player action,and what do I need to pay attention to while servicing?
David Schwoyer Dave's Piano service Piano Technician
|
|
|
|
Joined: Feb 2009
Posts: 1,764
1000 Post Club Member
|
1000 Post Club Member
Joined: Feb 2009
Posts: 1,764 |
I don't do much work on players, but I did take a player rebuilding course many years ago, so I can at least point out a few landmines to avoid. Make sure the player piano actually works before you do anything to it. Gently encourage the customer to demonstrate it for you. If the player has a transposing tracker bar, do not change the position. Often, an old player will continue working just fine even though the tubing is dry-rotted. If the tubing is dry-rotted and you change the position, the tracker bar tubing could all shatter like glass. Then you could have an angry customer that doesn't understand why his piano "worked fine until you touched it." Make a note of how the chain connects between the wind motor and spool box ( where the roll goes) so you can reconnect it correctly when you are done tuning... assuming you need to remove the wind motor. The main thing to look out for is dry-rotted tubes and cloth. Gently press on any tube you are going to disconnect to make sure it's pliable. Also, keep in mind that if a string should break... The thing is about older players, they can continue to work even if their parts are old and dry-rotted until their mechanisms are disturbed. Then, you could find yourself with a problem. Even though it's genuinely not your fault, it could be difficult to get a lay person to accept this. Now, if this is a newer piano, or one that has been rebuilt correctly, you're probably OK. Before going out to tune the piano, I think it would be a really good idea to contact the customer and get the brand name of the piano. You may then want to consider cross-posting to Piano World Forum's Mechanical Musical Instrument Forum for advice as to the specific brand of player you will be working on. Another really excellent resource is the Mechanical Musical Instrument Digest Forum available at < http://www.mmdigest.com/>. Also, there's an organization for player enthusiasts called AMICA (Automatic Musical Instruments Collectors Association) available here: < http://www.amica.org/Live/index.htm> Good Luck!
Last edited by daniokeeper; 03/22/09 12:29 PM.
Joe Gumbosky Piano Tuning & Repair www.morethanpianos.com (semi-retired) "The object in life is not to be on the side of the majority, but to escape finding oneself in the ranks of the insane." -Marcus Aurelius
|
|
|
|
Joined: Jun 2003
Posts: 32,060
Yikes! 10000 Post Club Member
|
Yikes! 10000 Post Club Member
Joined: Jun 2003
Posts: 32,060 |
You do not need to remove the mechanism to tune a player piano. You may need to undo a thing or two. There should be instructions printed somewhere on the piano.
Semipro Tech
|
|
|
|
Joined: Mar 2008
Posts: 4,263
4000 Post Club Member
|
4000 Post Club Member
Joined: Mar 2008
Posts: 4,263 |
Not sure if this is a late model player or an old one. If it is one of the older ones Joe is correct; things inside could be pretty crispy.......inform the customer if you have to disturb something this is done at the owners risk. In order to minimize string breakage, use a technique of lowering the sting pitch previous to pulling up for tuning.
BDB is correct, most of the time you just have to shift some things around a bit.
I just serviced a late model Aeolian from the 70’s, electric player… I had to remove the motor bracket only to move the motor to the side and tune the bass section. But of course all the tubing is relatively new and flexible, so no problems there.
Good luck with the job.Always good experience to do different models....
|
|
|
|
Joined: Oct 2008
Posts: 156
Full Member
|
OP
Full Member
Joined: Oct 2008
Posts: 156 |
Thanks for some of the advice.I did tell the client that I haven't done any players yet,and she kept the appointment,so at least she knows who she is hiring,and has the option of hiring someone with more experience.
David Schwoyer Dave's Piano service Piano Technician
|
|
|
|
Joined: Feb 2009
Posts: 1,764
1000 Post Club Member
|
1000 Post Club Member
Joined: Feb 2009
Posts: 1,764 |
At some point in your career, you may want to get a copy of Player Piano Servicing & Rebuilding by Art Reiblitz and keep it on your shelf as a reference.
For now, you're a student and there are far more important things for you to spend your money on. But, this is the best technical book I've ever seen on player pianos.
Last edited by daniokeeper; 03/22/09 03:43 PM.
Joe Gumbosky Piano Tuning & Repair www.morethanpianos.com (semi-retired) "The object in life is not to be on the side of the majority, but to escape finding oneself in the ranks of the insane." -Marcus Aurelius
|
|
|
|
Joined: Nov 2007
Posts: 6,828
6000 Post Club Member
|
6000 Post Club Member
Joined: Nov 2007
Posts: 6,828 |
Some older player pianos can be a real pain to work on if you get into regulation issues or string breakage. Especially the older ones where the old rubber tubes are brittle and ready to break off as soon as you touch them.
If you do break a string, it is highly likely that you will have to remove a bunch of this garbage to get it. Especially down below in the pedal area.
I don't touch them anymore. But, that is my personal preference.
Jerry Groot RPT Piano Technicians Guild Grand Rapids, Michigan www.grootpiano.comWe love to play BF2.
|
|
|
|
Joined: Oct 2006
Posts: 2,677
2000 Post Club Member
|
2000 Post Club Member
Joined: Oct 2006
Posts: 2,677 |
she ... has the option of hiring someone with more experience. Even experienced old-timers like me can have trouble with the brittle old player actions. Jerry Groot is probably wise to leave 'em alone. I haven't acquired that degree of wisdom yet, but I do ask owners to sign a short release now after one bad experience! I always offer to remove the action and dispose of it for free. I'm getting fewer and fewer takers. I think too many people are watching that durned Antiques Road Show, and think the crusty crumbling things are valuable.
|
|
|
|
Joined: Oct 2008
Posts: 156
Full Member
|
OP
Full Member
Joined: Oct 2008
Posts: 156 |
So,should I try to tune without removing any of the parts,and remove only if absolutely necessary?
David Schwoyer Dave's Piano service Piano Technician
|
|
|
|
Joined: Feb 2009
Posts: 1,764
1000 Post Club Member
|
1000 Post Club Member
Joined: Feb 2009
Posts: 1,764 |
So,should I try to tune without removing any of the parts,and remove only if absolutely necessary? That's my strategy. Please make sure the player still works before you touch it. Also, make sure all the keys play before beginning. If you see other issues... rusty strings, whole-step flat, action problems, never been tuned in living memory, etc... You have the right to politely decline to tune the piano. Don't run the risk of finding yourself in the position of adopting responsibility for problems that you didn't cause. I've never gotten into trouble for any job I turned down.
Last edited by daniokeeper; 03/23/09 12:19 AM.
Joe Gumbosky Piano Tuning & Repair www.morethanpianos.com (semi-retired) "The object in life is not to be on the side of the majority, but to escape finding oneself in the ranks of the insane." -Marcus Aurelius
|
|
|
|
Joined: Mar 2009
Posts: 88
Full Member
|
Full Member
Joined: Mar 2009
Posts: 88 |
Great advice on this subject. I would do a complete evaluation of the piano, looking for anything that is not as it should be. Put it in writing, show the customer the issues and have them sign the evaluation stating you are not the cause of these pre-existing problems. On most old players you can work around the stack without moving anything. Muting patterns often need improvised.
Some day you might pick up an old player and do a ground up rebuild to see just what is involved so you will be confident to work on them in the future. They are fun to work with. Good luck!
|
|
|
|
Joined: Mar 2008
Posts: 4,263
4000 Post Club Member
|
4000 Post Club Member
Joined: Mar 2008
Posts: 4,263 |
Yes in writing is a good idea...so is taking a couple of shots with the digital camera when you open up the front board....
|
|
|
|
Joined: Nov 2007
Posts: 6,828
6000 Post Club Member
|
6000 Post Club Member
Joined: Nov 2007
Posts: 6,828 |
Excellent idea of taking pictures with a digital camera!
Jerry Groot RPT Piano Technicians Guild Grand Rapids, Michigan www.grootpiano.comWe love to play BF2.
|
|
|
|
Joined: Nov 2008
Posts: 12
Junior Member
|
Junior Member
Joined: Nov 2008
Posts: 12 |
I have only encountered two players in my brief tuning career - a couple of Heintzman's. I don't know the design of other brands, but I have a hard time seeing how I could tune these pianos without removing the player mechanism. Sure, I could get at the tuning pins, but getting near the strings to mute them seemed impossible to me. Am I missing something?
I have considered charging people extra to tune players in the future because of the additional 20 minutes required to remove and replace the mechanism. It's not difficult, except for exercising the care mentioned in the previous replies, but it does take time.
Paul
Paul Clement Certified Piano Technician - UWO 2008
|
|
|
|
Joined: Oct 2008
Posts: 156
Full Member
|
OP
Full Member
Joined: Oct 2008
Posts: 156 |
wesquire,that someday was a few days ago.The only thing is,all of the player action was removed,except for the hand controls under the key slip.
It is a Bush and Lane built in Chicago.It was in an unheated garage for who knows how long.It had rodents living in it,as well as a nest over F#5 and G5 keys,those keys were chewed partway near the action.
I cleaned it out when I got it home,vacuumed out the keybed,and everywhere else.I wiped everything down inside and out.After that was done,I tuned it,and it was a 50 cents flat.It has dropped a little over the weekend,but it sounds so good,like a grand piano.
I know some of you might think I'm crazy for taking this one,but I know what to do if I can't do anything else with it.
David Schwoyer Dave's Piano service Piano Technician
|
|
|
|
Joined: Mar 2009
Posts: 88
Full Member
|
Full Member
Joined: Mar 2009
Posts: 88 |
David, If you teardown and completly rebuild a player you will gain a great understanding of how everything goes together and works so you will be confident in future encounters with tuning and servicing them. The advice given here is to save you a world of problems if you have a difficult customer.
|
|
|
|
Joined: Feb 2009
Posts: 1,764
1000 Post Club Member
|
1000 Post Club Member
Joined: Feb 2009
Posts: 1,764 |
If you do decide to get into rebuilding, you should absolutely know about this place: < http://www.playerpianocompany.com/player.html> They also have a copy of Rebuilding The Player Piano by Larry Givens as an online book you can read at no charge. < http://www.playerpianocompany.com/book.html> You'll want to read this reference as well as the Reiblitz player book. If I'm remembering correctly, the stack valve blocks on the Bush & Lane's player action were made of pig iron or some sort of cheap metal that became very brittle over time and fell apart. That's probably why the player action was missing. Before you decide on a project, research what will be involved. Some mechanisms are harder to rebuild than others. And, some are just not worth it anymore. Also, beware of rebuilding a player action that has been rebuilt before. If it wasn't rebuilt correctly, you could really be in for a time. Also, you should avoid rebuilding the more valuable player mechanisms like those in expression pianos and reproducing pianos until you become experienced. Good Luck
Last edited by daniokeeper; 03/23/09 11:33 PM.
Joe Gumbosky Piano Tuning & Repair www.morethanpianos.com (semi-retired) "The object in life is not to be on the side of the majority, but to escape finding oneself in the ranks of the insane." -Marcus Aurelius
|
|
|
|
Joined: Mar 2005
Posts: 961
500 Post Club Member
|
500 Post Club Member
Joined: Mar 2005
Posts: 961 |
I charge more for tuning a player, and take digital pics of everything before I move anything...after almost 3 decades of rebuilding players, I usually know what goes where...but tubing schematics or unusual configurations (to escape patent issues, no doubt) still can cause problems...
An additional $20 is not unreasonable to take out, or tilt the player stack to tune it...and, the tunings take longer because you have to reach further around things.
Beware though...old mechanisms with rotted cloth and hoses/tubes will fall apart and you'll be blamed. I only tune old player pianos after delivering a rebuilding estimate first, so there is no doubt that both my customer and I agree it needs rebuilding.
Player Piano Company is, at last check, out of the picture...Durell Armstrong passed away, and the company doesn't answer the phone (unless this changed this week). My understanding is that it is unclear if/when they will re-open. This is painful for those of us who order most of our player supplies from that source. We'll need to stay tuned....
RPD
MPT(Master Piano Technicians of America) Member AMICA (Automated Musical Instruments Collector's Association) (Subscriber PTG Journal) Piano-Tuner-Rebuilder/Musician www.actionpianoservice.com DEALER Hailun Pianos
|
|
|
|
Joined: Feb 2009
Posts: 1,764
1000 Post Club Member
|
1000 Post Club Member
Joined: Feb 2009
Posts: 1,764 |
Player Piano Company is, at last check, out of the picture...Durell Armstrong passed away, and the company doesn't answer the phone (unless this changed this week). My understanding is that it is unclear if/when they will re-open. This is painful for those of us who order most of our player supplies from that source. We'll need to stay tuned.... How very sad... I hadn't heard. < http://www.cozinememorial.com/obituary.php?id=46>
Joe Gumbosky Piano Tuning & Repair www.morethanpianos.com (semi-retired) "The object in life is not to be on the side of the majority, but to escape finding oneself in the ranks of the insane." -Marcus Aurelius
|
|
|
|
Joined: Mar 2005
Posts: 2,726
2000 Post Club Member
|
2000 Post Club Member
Joined: Mar 2005
Posts: 2,726 |
Here is another good website for Player Piano Care etc.... http://www.player-care.com/index.html
|
|
|
|
|
Piano
by Gino2 - 04/17/24 02:34 PM
|
Piano
by Gino2 - 04/17/24 02:23 PM
|
|
|
Forums43
Topics223,405
Posts3,349,434
Members111,637
|
Most Online15,252 Mar 21st, 2010
|
|
|
|
|
|