This custom search works much better than the built in one and allows searching older posts.
|
|
69875 Members
40 Forums
143472 Topics
2075487 Posts
Max Online: 15252 @ 03/21/10 11:39 PM
|
|
|
#2003717 - 12/23/12 11:35 PM
Build a PinBlock Drill
|
Full Member
Registered: 12/06/05
Posts: 329
Loc: Stoneham, MA
|
Well in the process of learning what it takes to rebuild a piano I've found that Pintight doesn't work and CA glue is well (You Know) and if your going to spend the time and effort to rebuild then a new PinBlock is a must. I'm doing piano rebuilds just for fun at this point so I built an (in the piano) PinBlock Drill. All bearings and rods are bought on eBay or scavenge. the drill should be better but seems to work OK. I butchered some Stanley laser lines for aligning the drill. I also found that not vacuuming the sawdust helps with the laser alignment by filling the un-drilled holes. So far all test drilling s seem to work out great.    
Edited by woodfab (12/24/12 12:33 AM)
_________________________
Dan (Piano Tinkerer)
|
|
Top
|
|
|
|
|
#2003720 - 12/23/12 11:57 PM
Re: Build a PinBlock Drill
[Re: woodfab]
|
2000 Post Club Member
Registered: 01/20/09
Posts: 2763
|
I'm impressed!
_________________________
B.Mus. Piano Performance 2009
M.Mus. Piano Performance & Literature 2011
PTG Associate Member
|
|
Top
|
|
|
|
|
#2003766 - 12/24/12 03:38 AM
Re: Build a PinBlock Drill
[Re: woodfab]
|
4000 Post Club Member
Registered: 03/14/08
Posts: 4218
Loc: France
|
Nice setup, can you regulate inclination? cooling the bits seem to be necessary, for new pinblock it is certainly.
|
|
Top
|
|
|
|
|
#2003815 - 12/24/12 08:32 AM
Re: Build a PinBlock Drill
[Re: woodfab]
|
Full Member
Registered: 12/06/05
Posts: 329
Loc: Stoneham, MA
|
It can easily be angled up to 7˚. I will be adding some type of cooling 
_________________________
Dan (Piano Tinkerer)
|
|
Top
|
|
|
|
|
#2003828 - 12/24/12 08:41 AM
Re: Build a PinBlock Drill
[Re: woodfab]
|
Full Member
Registered: 12/15/09
Posts: 302
Loc: Vojvodina, Serbia
|
Great tool! Congratulations. I would live to have that here!
_________________________
Bojan Babić
piano technician and tuner
Šid, Vojvodina, Serbia
_____________________________
bojanbabic@yahoo.com
|
|
Top
|
|
|
|
|
#2003964 - 12/24/12 01:33 PM
Re: Build a PinBlock Drill
[Re: woodfab]
|
4000 Post Club Member
Registered: 03/14/08
Posts: 4218
Loc: France
|
Nice ! where are the rods coming from ? they make me think of a robot done by a friend with an old bubble jet printer, he made use to make holes in the carboard strips for an organ (midi)
I was shown to use 2 pieces of adhesive ribbon to make 2 flaps around the drill, it send the dust away and produce a little air.
probably not enough to cool a bit in a Delignit block...
Edited by Kamin (12/24/12 02:49 PM)
|
|
Top
|
|
|
|
|
#2003979 - 12/24/12 01:53 PM
Re: Build a PinBlock Drill
[Re: Olek]
|
Full Member
Registered: 01/12/10
Posts: 364
Loc: Boone, Iowa, USA
|
Hi Dan - If you would remind me how to post a photo, I'll show you a picture of how I direct a constant airstream at the bit that will keep it cool, no matter what type of block you're drilling - if your bit is good and sharp, at any rate. Chuck Behm
_________________________
"The act of destruction is infinitely easier than the act of creation" - Arthur C. Clarke
|
|
Top
|
|
|
|
|
#2004001 - 12/24/12 02:45 PM
Re: Build a PinBlock Drill
[Re: woodfab]
|
Full Member
Registered: 04/10/08
Posts: 287
|
I have seen something similar to this (a few years ago) that stood on legs and stradled the keyboard length of the piano.
I think it may have been from mazaglia tools.
Otherwise very nice!
Edited by Mark Davis (12/24/12 02:47 PM)
Edit Reason: minor addition
_________________________
Mark Davis
Pianoforte Technologies
Piano Tuner & Technician
|
|
Top
|
|
|
|
|
#2004123 - 12/24/12 09:31 PM
Re: Build a PinBlock Drill
[Re: woodfab]
|
3000 Post Club Member
Registered: 04/09/06
Posts: 3029
Loc: Vancouver B.C. Canada
|
Nice job.
_________________________
Verhnjak PianosSpecializing in the Restoration, Refinishing & Maintenance of Fine Heirloom Pianos Exclusive Dealer For Charles R. Walter Pianos www.pianoman.ca Verhnjak Pianos Facebook
|
|
Top
|
|
|
|
|
#2004263 - 12/25/12 11:06 AM
Re: Build a PinBlock Drill
[Re: woodfab]
|
Full Member
Registered: 12/06/05
Posts: 329
Loc: Stoneham, MA
|
Thanks guys The two long rods that run across the piano left to right came off an exercise machine. They're 1" thick and keep the drill quite stable when drilling. Rather than having legs that reach to the floor it sits on the edge of the piano. This makes it easy to store when not in use. 
_________________________
Dan (Piano Tinkerer)
|
|
Top
|
|
|
|
|
#2004685 - 12/26/12 05:29 PM
Re: Build a PinBlock Drill
[Re: woodfab]
|
Full Member
Registered: 11/09/11
Posts: 75
Loc: Cincinnati, OH
|
Very nice job, indeed.
Thanks for posting the pictures and story, Dan.
Edited by Steve in Cincy (12/26/12 05:30 PM)
_________________________
Regards,
Steve Schutte
Cincinnati
1979 6'7 Kimball Grand
1902 5'10 Hazelton Bros. Grand (project piano)
|
|
Top
|
|
|
|
|
|
Del.icio.us
|Contact |
Privacy | Legal | About Us | Site Map | Free Newsletter | Press Room |
Previous Topic
Index
