Piano World Home Page Forums Our Most Popular Forums Piano Tuner-Technicians Forum Ar Steinway whippens beter than Kimball whippens

Here's what I'm thinking.
I'm cleaning up this 1932 Kimball.
I repaired the sound board cracks, removed old finish and fixed veneer then 8 coats of lacquer. I cleaned and painted the plate and put a new pin block. Now I'm playing around with the action.
Cleaned key-frame, new felt, key-tops, hammers and shanks.

Now I'm thinking I should learn how to clean, lube, and regulate the wippens.

Well the whippens are 82 years old and look their age.

I have a set of Steinway whippens that are only 6 years old.

It appears that all the contact points line up the same as the Kimball ones.

Has anyone done this and what problems will I have?

Can't tell from your photo . . .

Does the capstan contact point (wippen heel) line up at the same time as the jack toes line up and the flange rail centerpin?

What about the screw hole of the wippen flange? Is it the same offset from the centerpin?

Also, how are you going to make the flange fit the rail? You can't change the brass flange onto the S&S wippen.

The Steinway wippen has the advantage of the butterfly spring which is supposed to be faster for repetition. That wippen is way more than 6 years old though! Like Keith says - that brass flange seems like it would be the major stumbling block. You can always try a sample and see if you can get it to work. Anytime you change parts on a piano you need to try samples first.

Why can't you just rebuild the original whippens? It'll be good for you!

It looks like the Kimball whippen has a completely different flange set up. The Kimball might not have enough room for the rest felt on the Steinway whippens. And the area of the upper repetition lever that contacts the drop regulating screw looks different.

I don't think it's going to fit, but let us know.

Greetings
Just pin one of them up and install it, It will tell you what is going to work or not. You should be very well versed in the difference that the spread makes, and how your intersecting arcs are relating to one another.
Regards,

Huh?? Did you see the photo?

Even if it seem to work on one note it is very difficult to be sure that the touch will be good.

Also as it have been said there is no space for the rest cushion, even the pinning seem to be a differnt type.

The idea to put "Steinway parts" is sort of myth I found sometime with hammer heads. rarely appropriate in the end BTW

The capstan also have to be inclined for those whippens (seem to me)
Those are old Steinway whippens, possibly German, while I dont reclal having seen that red cloth around the rest cushion, may be on some older ones but I have my doubts.

What dimension is the jack ?

Its a no-hope-er. The flange setup is reversed from the S&S. It looks more like a hammer shank flange setup than a standard whip flange setup.

Chickering whips have the same set up to accomodate the brass flange.

Did this Kimball have brass flanges?

Jim Ialeggio

I put one in to see what problems I would run into.
I would modify or remake the whippen rail.
I actually have a second action for this piano so if it doesn't work out it's won't be a problem.
And looks like I would have to raise the let-off rail.

Based on your latest photos, it kinda looks like it might work. You will want either to use thinner let-off buttons or move the let-off rail. Dunno if you can move it in the right direction . . .

If you are just doing this as an educational project, I don't see why not. The shanks/flanges are also prime suspects for replacement . . .

not with those capstans

Why do you say that? The capstan marks line up in the first photo. The only problem I can see is the jack tender (toe).

It is true that there is no photo that actually shows the capstan under the new wippen heel . . .

My bad...looks like you could get it going after a fashion, doesn't it...

Still curious, and can't see from the pic, what the old flange looks like.

Jim Ialeggio

I think it's a Billings brass flange.
I do wonder how well the flange is mated to the rail, though. If there's flex in the flange because the S&S profile doesn't contact the rail properly, there could be instability over time.

I think "after a fashion" covers it . ..
Clearly not the approach most of us would take, but for someone learning for fun . . .

I'm pretty sure I can get everything to line up.
I would mold the shape of the whippen-rail to accommodate the whippen flange properly.
I have a new set of hammers and shanks which I'll have to re-adjust the back-checks.
I raised the let-off rail 1/16" with a washer which seems to work.

But molding the wippen rail will also bring the wippen foward. Moving it a little (like 1/32") can have some impact on the leverage. You could relocate the action back on the keyframe the same amount if you have enough space at the keyslip to accommodate moving the whole action/keyframe forward the same amount to maintain hammer strike.

The let-off rail doesn't move up. It moves up and forward. Is that OK?

If you are going to play with this stuff, you have to be aware of everything that is happening and a bit picky.

OK I molded the rail and the mounting holes are slotted in order to move it back or forth.

OK, the slotted rail is another possibility. Just keep in mind that moving the wippen rail is not the same as moving the entire action stack over the capstans.

It may help you out with the jack toe to regulating button alignment, though . . .

But the molded profile still doesn't seem to match the unique S&S profile.

The fact still remains: Those are very old wippens, not the 6 year old wippens the OP thought they were. If your going to change the wippens, at least think about using some new ones. All that labor to install old parts. But a new set will set you back a pretty good chunk of change, so I guess I can sympathize, especially if this is just your own piano and you are wanting to experiment.